东莞市翼辉机械设备有限公司为您免费提供超声波塑胶焊接机鱼尾夹厂家蝌蚪夹厂家等相关信息发布和资讯,敬请关注!
line
档案盒压名片袋纸卡自动机
产品名称:

档案盒压名片袋纸卡自动机

产品型号:
产品简介:

详细介绍
胶纸复合贴片机
Paper and plastic composite Labeling machine
一 : Introduction of equipment
Equipment workflow:
1:Before the machine starts, first of all need to be placed in the position 4(picture 1) of the adhesive tape coil. And the coil will be wound through position 3,2,1componets to prepare the work(winding method ); at the same time, the required pieces of paper need to be put into the warehouse in picture two,position 9,and adjust the position. 
2: Open the machine, First, manually adjust the panel manual feeding (1), so that the initial coil level without scratches, and then adjust to automatic block, at this time do not need to put the product, need to take the tape film punching position to the knife position; wait for the temperature of hot-pressing die to rise to 115 degrees above when the start of work.

3: Automatic adjustment, Each time the start button is pressed, Part 8 delivers the sheet to a fixed position in Slice Module 2, while Slice Module 2 cuts the sheet to the desired size and overlaps the sheet, and then Component 7 delivers the overlapped sheet of paper and adhesive together to the bottom of the hot-pressing die, and finally carries out the hot-pressing molding.

The entire workflow is in view of the equipment has been adjusted (due to different customer products and other reasons, the need to adjust the corresponding parameters, not described here).

1:机器开机之前首先需将胶带卷放置在下图一的4位置上,并且将卷料经过3,2,1这几个组件进行缠绕,准备工作(缠绕方法);同时需将所需要的纸片放入图二9中的料库,并调节好位置;
2:开机,首先手动调节面板手动放料(即组件1),让卷料初始段平整无刮伤,然后调成自动挡,此时不需放产品,需将胶带卷料有冲孔的位置送到切刀位置;等待热压模具的温度升高到115°以上时可开始工作;
3:调成自动,当每按下开始按钮时,步件8将纸片送到切片组件2的固定位置,同时切片组件2将胶片切到所需尺寸和纸片重叠,然后组件7将重叠的纸片和胶料一起输送到热压模具下面,最后进行热压成型。
整个工作流程是鉴于设备已经调整好(因客户产品的不同及其他原因,需要进行相应的参数调整,此处不介绍)。

1:Feeding and cutting components
2:Punching tape side hole components   
3:Roll components
4:Feed components
5:Waste collection cover
6:Hot pressing film welding components  

7:Adhesive tape and paper feeding components
8:Paper feed components
9:Paper storehouse components
二:Safety precautions 
1: hot pressing die for heating element, do not touch hands when working, prevent scalding;
2: In the process of automatic operation, do not put hand or other parts of the body into the conveyor structure to prevent clamping;
3: When there is a foreign body under the hot-pressing die, do not use the hand to remove directly, should use a brush and other auxiliary tools to remove, to prevent hand scratches.

时间:2019/5/13 0:00:00
返回列表

相关新闻

line

自动折边熔接机哪家好?供应订做多少钱?东莞超音波模具批发怎么样?诚信公司专业以批发价格大量现货提供超音波模具自动折边机自动上胶折边机超声波塑胶焊接机等品质优良的产品及报价,欢迎来电生产定制!

联系电话: 0769-87568100 传真: 0769-87568303 邮箱: 136611273@qq.com

XML网站地图手机网站 备案号:粤ICP备17156017号-1

技术支持:

在线客服
热线电话
手机网站